Power Switch  
Parts No. Features VCC(Max) PD(mW) ICC ISTBY RON IO(limit) Package
L88312 SHORT CIRCUIT PROTECT BLOCK FOR LNB


* Wide operating voltage range: 8V~32V
* Low on resistance:320 mΩ
* Constant current set by external resistor
* Thermal shutdown
8V~32V - <6mA - Typ=320mΩ Typ=0.37A SOP-8
US2005 70mΩ, 0.5A High-Side Power Switches With Flag


* Built-in 80mΩ N-MOSFET
* Open-drain fault flag output to Indicate fault conditions
* Input voltage varies from 2.5V to 5.5V
* 80μA low quiescent current
* Current limit values of 0.5A, 0.8A, and 1.2A
* Automatic-on output after fault
* Thermal protection
* Under voltage lock-out (UVLO)
2.5V~5.5V 250mW <300uA <5uA Typ=70mΩ Typ=0.7A SOT-26
US3075-US3375 0.5A Power Distribution Switch

* Operating on The Range of 3V to 5.5V
* High-Side MOSFET with 100mΩ RDS(ON) (TYP.)
* Quiescent Supply Current: 65μA
* Available With 4 Versions of Current Limits with Foldback
* Rise Time: 400μS (TYP.)
* UVLO (Under Voltage Lockout)
* Output Shutdown Pull-low Resister
* Shutdown Supply Current: 1μA (MAX.)
* Available with Active-Low / High Enable
* Reverse Current is Not Generated when in Power Off State
* Deglitched Open-Drain Over-Current Flag Output (OC )
*US3075:0.5A ; US3175:0.7A ; US3275:1.1A ; US3375:1.5A
3.0V~5.5V 470mW Typ=65uA <1uA Typ=100mΩ  Typ=0.75A SOP-8 MSOP-8 TSSOP-8
US201/A/B/C 0.6A High-Side Power Switches With Flag

* 80mΩ(Typ) N-Channel MOSFET
* Supply Current:
– Switch On : 25μA(Typ)
– Switch Off : 1μA (Typ)
* Load Current 500mA for US201 and 1.0A for US201A/B/C
Blank:0.6A,A:1.1A,B:1.3A,C:1.5A ; J:Active High L:Active Low
* Input Voltage from 2V ~ 5.5V
* In Off-State: Output Voltage can be Higher than Input
2.0V~5.5V 250mW <45uA <1uA Typ=80mΩ Typ=0.8A SOT-25
US107 2.2A POWER DISTRIBUTION SWITCH

* Single power switch family
* Operating range: 3.0V~5.5V
* 130μA quiescent supply current
* 1μA maximum shutdown supply current
* 70mΩ high-side MOSFET
* 1mS typical rise time
* Under voltage lockout
* Available with Active-Low / High Enable
A:2.2A , B:1.7A , C:1.2A
* No reverse current when power off
* Available with or without output shutdown pull-low
resister
* Deglitched open-drain over-current flag output (OC )
* Output reverse-voltage protection
3.0V~5.5V 500mW <190uA <1uA Typ=70mΩ Typ=2.2A SOT-25
US203 80mΩ/90mΩ, 0.6A High-Side Power Switches With Flag

* Input Voltage Varies From 3.5V to 5.5V
* Built-in N-MOSFET
* Output Can Be Forced Higher Than Input (Off-State)
* Typical Low Supply Current:
- Switch On: 25μA (TYP)
- Switch Off: 0.1μA (TYP)
* Open-Drain Fault Flag Output To Indicate Fault
Conditions
* Protection Circuits:
- Soft-start( Hot plug-in application)
- UVLO 1.7V (TYP.)
- Current Limiting Protection
- Thermal Shutdown Protection
* Reverse Current Flow Blocking (No Body Diode)
*AH:2.1A / Active High, AL:2.1A/Active Low
BH:1.6A / Active High, BL:1.6A/Active Low
CH:1.1A / Active High, CL:1.1A/Active Low
DH:0.6A / Active High, DL:0.6A/Active Low
3.5V~5.5V 250/400mW <45uA <1uA Typ=80mΩ/90mΩ Typ=0.8A SOT-25 SOP-8
US202 1.1A 100mΩ Power Distribution Switches

* Input Voltage Varies From 2.2V to 6V
* Guaranteed Continuous Current: 1.0A
* High-Side NMOSFET: 85mΩ (TYP)
* Soft Start
* Current Limit:1.5A
* Thermal Protection
* Low Supply Current: 23μA
* Available with Active-Low / High Enable
2.2V~6.0V 250mW <45uA <1uA Typ=85mΩ Typ=1.5A SOT-25
US3177H 0.75A Power Distribution Switch Active High 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=1.0A SOP-8 MSOP-8
US3177L 0.75A Power Distribution Switch Active Low 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=1.0A SOP-8 MSOP-8
US3277H 1.2A Power Distribution Switch Active High 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=1.5A SOP-8 MSOP-8
US3277L 1.2A Power Distribution Switch Active Low 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=1.5A SOP-8 MSOP-8
US3377H 1.6A Power Distribution Switch Active High 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=2.0A SOP-8 MSOP-8
US3377L 1.6A Power Distribution Switch Active Low 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=2.0A SOP-8 MSOP-8
US3477H 2.0A Power Distribution Switch Active High 2.7~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=2.5A SOP-8 MSOP-8
US3477L 2.0A Power Distribution Switch Active Low 2.7~5.5V - Typ=65uA <1uA Typ=100mΩ  Typ=2.5A SOP-8 MSOP-8
US3577H 2.8A Power Distribution Switch Active High 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ Typ=3.7A SOP-8 MSOP-8
US3577L 2.8A Power Distribution Switch Active High 2.7V~5.5V - Typ=65uA <1uA Typ=100mΩ Typ=3.7A SOP-8 MSOP-8
US210AD 160mΩ, 2.5A High-Side POWER-DISTRIBUTION
SWITCHES
* Operating range: 2.7V~5.5V
* High-side MOSFET: 160mΩ (TYP.)
* Quiescent supply current: 25μA(TYP.)
* Standby supply current: 1μA (Max.)
* 1A Continuous Output Current* Programmable current limit,
1A(TYP.)
* Reverse input-output voltage protection
* Built-in soft-start
* Under-voltage Lockout
2.7V~5.5V - <45uA <1uA Typ=160mΩ Typ=1.1A SOT-25
US205 100mΩ, 2A High-Side Power Switches With Flag

* High-Side NMOSFET: 100mΩ (TYP)
* Input Voltage Varies From 2.7V to 5.5V
* Low Supply Current: 20μA
* Over Current Protection
* Short Circuit Protection
* Under Voltage Lockout
* Thermal Protection with Foldback
* Slew Rate Limited Turn-On Time 3ms (5V)
* Reverse Blocking Current
* RoHS Compliant
* Available with Active-Low / High Enable
2.7V~5.0V 300mW <70uA <1uA Typ=100mΩ Typ=2.0A SOP-8
US206 0.7A POWER DISTRIBUTION SWITCH

* Operating on The Range of 3.0V to 5.5V
* High-Side MOSFET with 85mΩ RDS(ON)
* Quiescent Supply Current: 65μA
* Available With 4 Versions of Current Limits with Foldback
* Rise Time: 400μS (TYP.)
* UVLO (Under Voltage Lockout)
* Output Shutdown Pull-low Resister
* Shutdown Supply Current: 1μA (MAX.)
* Logic Level Enable Pin, Available with Active-High or Active-Low Version
* Reverse Current is Not Generated when in Power Off State
* Deglitched Open-Drain Over-Current Flag Output (OC )
3.0V~5.5V 400mW <65uA <1uA Typ=95mΩ Typ=0.7~2.0A SOT-25
US1528 2.0A USB High-Side Power Switch Advance Information

* Open-Drain Fault Flag
* Low on-Resistance MOSFET: Typical 110mΩ(at 5.0V)
* Operating Voltage Varying From 3.0V to 5.5V
* Output can be Forced Higher than Input when Operating in Off State.
* Slow Turn-On (Soft-Start) and Fast Turn-Off
* On-State Supply Current: 100 μA (TYP)
* Standby Supply Current: 1μA (TYP)
* Current Limit: 1.4A (TYP)
* Thermal Shutdown Protection Circuit
* UVLO (Under-Voltage Lockout): 2.4V (TYP)
* Available with Active-Low / High Enable
3.0V~ 5.5V 470mW <160uA <5uA Typ=110mΩ Typ=2.7A SOP-8
US2076 0.5A Dual USB high side power swtich Active High
Output Rise Rime 500μs Typical

* MOSFET with Low On-Resistance: 140mΩ max.@5.0V per Channel
* Continuous Load Current: 500mA (MIN.) per Channel
* Off-State Supply Current: 1μA (TYP.)
* Output can be Forced Higher than Input (Off-State)
* Current Limit up to 1.25A (MAX.)
* Input Supply Voltage: 3.0V ~ 5.5V
* On-State Supply Current: 110μA (TYP.)
* Thermal Shutdown Protection Circuit
* UVLO (Undervoltage Lockout): 2.4V (TYP.)
* Open-Drain Fault Flag
* 1ms Turn-On (Soft-Start) and Fast Turn-Off
* Compliant to USB Specifications
* Available with Active-Low / High Enable
3.0V~ 5.5V 470mW Typ=110uA Typ=25uA <100mΩ  Typ=0.75A SOP-8
US3076-US3376 0.5A Dual USB High-Side Power Switch

* Operating on the Range of 3V to 5.5V
* High-Side MOSFET with 87mΩ RDS(ON)
* Quiescent Supply Current: 65μA
* Available with 4 Versions of Current Limits with Foldback
* Rise Time: 400μS (TYP)
* UVLO (Under Voltage Lockout)
* Shutdown Supply Current: 1μA (MAX)
* Reverse Current is not Generated when in Power Off State
* Deglitched Open-Drain Over-Current Flag Output (OC )
* Available with Active-Low / High Enable
* US3076:0.75A, US3176:1A, US3276:1.5A, US3376:2A
2.7V~5.5V 470mW <150uA <1uA Typ=87mΩ  Typ=0.75A SOP-8 MSOP-8
US16855 0.6A Dual USB High-Side Switch for USB Application  Active High

* 4V ~ 5.5V operating range
* Two P-channel power MOSFET control switch
* Over-current protection
* Under-voltage lockout circuit
* Thermal shutdown circuit
* Soft-start circuit
* Flag indicates fault conditions
4.0V~5.5V 300mW <1.5mA <5uA Typ=100mΩ  Typ=0.9A SOP-8
US2075A 0.8A Dual Channel Power Distribution Control Switch for USB
Output Rise Time 5.0ms Typical active-low

* 100 μA MAX operating current
* 5μA MAX standby current
* 3.5V ~ 5.5V operating range
* Two P-channel power MOSFET control switch
* Over-current protection
* Under-voltage lockout circuit
* Thermal shutdown circuit
* Soft-start circuit
* Flag indicates fault conditions
3.5V~ 5.5V 300mW <100uA <5uA Typ=105mΩ Typ=0.9A SOP-8
US2075C 0.6A Dual Channel Power Distribution Control Switch for USB
Output Rise Time 5.0ms Typical active-high

* 100 μA MAX operating current
* 5μA MAX standby current
* 3.5V ~ 5.5V operating range
* Two P-channel power MOSFET control switch
* Over-current protection
* Under-voltage lockout circuit
* Thermal shutdown circuit
* Soft-start circuit
* Flag indicates fault conditions
3.5V~ 5.5V 300mW <100uA <5uA Typ=105mΩ Typ=0.9A SOP-8
US2175 Dual USB High Side Power Switch Active High

* Open-Drain Fault Flag.
* High-Side MOSFET Switch with 5V Input Voltage
* 110mΩ RDS(ON) Meets USB Voltage Drop Requirements for Maximum Transmission Wire Length
* Load Current: 1A
* Output Can be Forced Higher Than Input (Off-State)
* On-State Supply Current: 65μA (TYP.)
* Off-State Supply Current:.1μA (TYP.)
* Current-Limit / Short Circuit Protection and Thermal Shutdown Protection Under Overcurrent Condition
* UVLO Makes the Switch OFF at Start UP
* With Slow Turn ON and Fast Turn OFF
* Enable Active-Low or Active-High
7.0V 625mW Typ=65uA Typ=1uA Typ=110mΩ Typ=1.3A SOP-8
US2026A Dual Channel USB Power Switch and Over Current Protection
Output Rise Time 160μs Typical

* Two P-channel power MOSFET control switch
* 110μA Max operating current
* 5μA Max standby current
* 145 mΩ Max switch resistance
* 2.7V ~ 5.5V input voltage range
* 500mA minimum continuous load current
* Smooth turn-on eliminates in-rush induced voltage drop
* 1 ms fault flag delay filters Hot-Plug events
* Over-current protection
* Under-voltage lockout circuit
* Thermal shutdown protection
* Flag indicates fault conditions
2.7V~ 5.5V 300mW <110uA <5uA Typ=105mΩ Typ= 1.5A SOP-8
US204 100mΩ, 1.1A Dual High-Side Power Switches With Flag

* 100mΩ(Typ) N-Channel MOSFET
* Supply Current:
– Switch On : 60μA (Typ)
– Switch Off : 1μA (Typ)
* Load Current 1.5A for US204AH/AL and 1.0A for US204CH/CL
* Input Voltage from 2V ~ 5.5V
* In Off-State: Output Voltage can be Higher than Input
*AH:1.5A/Active High, AL:1.5A/Active Low
CH:1A/Active High, CL:1A/Active Low
2.0V~5.5V 300mW <90uA <1uA Typ=100mΩ Typ=1.5A SOP-8
US94060 High-Side Power Switch Active High Ton_Dly 0.85us                                        

* Operating voltage range:1.8V ~ 5.5V
* Providing 2A continuous operating current
* P-channel MOSFET’s RON : 175mΩ typical
* Built-in level shift for control logic
* Quiescent current is as low as 2μA
* Micro-power shutdown less than 1μA
1.8V~5.5V 270mW Typ=2uA <1uA Typ=175mΩ - SOT-26
US94061 High-Side Power Switch Active High Ton_Dly 0.85us Rshutdown 200Ω

* Operating voltage range:1.8V ~ 5.5V
* Providing 2A continuous operating current
* P-channel MOSFET’s RON : 175mΩ typical
* Built-in level shift for control logic
* Quiescent current is as low as 2μA
* Micro-power shutdown less than 1μA
* Built-IN Level Shift Circuitry:
Controlled 1μs Turn-ON Rise-Time
Fast 60ns Turn-OFF Fall Time
* Built-IN Fast-OFF Load Discharge Circuit
1.8V~5.5V 270mW Typ=2uA <1uA Typ=175mΩ - SOT-26
US94062* High-Side Power Switch Active High Ton_Dly 700us 1.8V~5.5V 270mW Typ=2uA <1uA Typ=175mΩ   SOT-26
US94063* High-Side Power Switch Active High Ton_Dly 700us Rshutdown 200Ω 1.8V~5.5V 270mW Typ=2uA <1uA Typ=175mΩ   SOT-26
US12231 Power Interface Switch Active High

* Meets the ExpressCardTM standard (ExpressCard|34 or
ExpressCard|54)
* Compliant with the ExpressCardTM compliance checklists
* Fully satisfies the ExpressCardTM implementation guidelines
* Supports systems with WAKE function
* TTL-Logic compatible inputs
* Short circuit and thermal protection
* -40°C ~ 85°C ambient operating temperature range
3.0V~3.6V 704.2mW <150uA <1uA Typ=120mΩ Typ=1.3A TSSOP-20
US211 0.6A High-Side Power Switches With Flag

* 80mΩ(Typ) N-Channel MOSFET
* Supply Current:
– Switch On : 25μA(Typ)
– Switch Off : 1μA (Typ)
* Load Current 500mA for US211 and 1.0A for US211A/B/C
Blank:0.6A, A:1.1A, B:1.3A, C:1.5A
* Input Voltage from 2V ~ 5.5V
* In Off-State: Output Voltage can be Higher than Input
* Available with Active-Low / High Enable
2.0V~5.5V 250mW <45uA <1uA Typ=80mΩ Typ=0.8A SOT-25
US212 0.5A SINGLE CHANNEL CURRENT-LIMITED POWER SWITCH

* Single USB Port Power Switches
* Over-Current and Thermal Protection
* 0.8A Accurate Current Limiting
* Reverse Current Blocking
* 110 mΩ On-Resistance
* Input Voltage Range: 2.7V~5.5V
* 0.6ms Typical Rise Time
* Very Low Shutdown Current: 1μA (max)
* Fault Report (FLG) with 7ms deglitch capability
* Ambient Temperature Range -40°C~+85°C
* Available with Active-Low / High Enable
2.7V~5.5V - <70uA <1uA Typ=110mΩ Typ=0.5A SOP-8
US222 2.0A High-Side Power Switches With Flag

* Low MOSFET On Resistance: 85mΩ
* Compliant to USB Specifications
* Available 4 Versions of Continuous Load:
AL/AH: 2.0A, BL/BH: 1.5A, CL/CH: 1.0A, DL/DH: 0.5A
* Logic Level Enable Pin: Available with Active-high or Active-low Version
* Low Supply Current: 68μA (Typ.)
* Low Shutdown Current: 1.0μA (Max)
* Soft Start-up
* Under-voltage Lockout
* Over-current Protection
* Over Temperature Protection
* Load Short Protection with Fold-back
* Deglitched FLAG Output with Open Drain
* No Reverse Current When Power Off
* With Output Shutdown Pull-low Resistor
5.5V - <95uA <5uA Typ=85mΩ Typ=2.0A SOT-25
US223 2.1A High-Side Power Switches With Flag

* Input Voltage Varies From 3.5V to 5.5V
* Built-in N-MOSFET
* Output Can Be Forced Higher Than Input (Off-State)
* Typical Low Supply Current:
- Switch On: 25μA (TYP)
- Switch Off: 0.1μA (TYP)
* Open-Drain Fault Flag Output To Indicate Fault
Conditions
* Protection Circuits:
- Soft-start( Hot plug-in application)
- UVLO 1.7V (TYP.)
- Current Limiting Protection
- Thermal Shutdown Protection
* Reverse Current Flow Blocking (No Body Diode)
*AH/AL: 3.2A, BH/BL: 2.5A, CH/CL: 1.8A, DH/DL: 1.1A
3.5V~5.5V 400mW <120uA <1uA Typ=80mΩ Typ=2.1A SOT-25
US251 0.5A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES

* Single Power Switch Family
* 80-mΩ High-Side MOSFET
* Rated currents of 0.5 A, 1 A, 1.5 A, 2 A
* Accurate, Fixed, Constant Current Limit
* Deglitched Fault Reporting
* Output Discharge When Disabled
* Reverse Current Blocking
* Built-in Softstart
* Current Limit:08: 0.8mA, 16: 1.6mA, 22: 2.2mA, 29: 2.9mA
3.5V~5.5V - <70uA <1uA Typ=80mΩ Typ=0.6~2.3A SOT-25
US236H * Operating Range: 4.5V~5.5V
* Quiescent Supply Current: 50uA (TYP.)
* Standby Supply Current: 1μA (Max.)
* Output Voltage Switch to 5VSB at S3/S4/S5
400mΩ High Side Switch
200mA Continuous Load Current
* Output Voltage Switch to 5VCC at S0/S1/S2
80mΩ High Side Switch
1.5A Continuous Load Current
* Built-in Soft-Start
* Fast Turn Off
* Enable Active-High
* Meets USB Current-Limiting Requirements
4.5V~5.5V 625mW <70uA <1uA Q1: Typ=80mΩ
Q2: Typ=400mΩ
Q1: Typ=2.3A
Q2: Typ=0.75A
SOP-8
US301 0.2A SINGLE CHANNEL CURRENT-LIMITED LOAD SWITCH

* Input voltage range: 2.7V~5.2V
* Short-circuit protection and fast response time
* Accurate current limiting: 0.4A
* On-resistance:250 mΩ
* Reverse-current blocking
* Soft-start with 0.7ms typical turn-on time
* Over-current and over-voltage protection
* Thermal protection
* Ambient temperature range: -40°C~+85°C
2.7V~5.2V - <125uA <0.1uA Typ=250mΩ Typ=0.2A SOT-23-3
US2236032DB ULTRA SMALL, LOW INPUT VOLTAGE, LOW RON, LOAD SWITCHES

* Integrated P-Channel Load Switch
* Input Voltage: 1V to 3.6V
* 1 A Maximum Continuous Switch Current
* On-Resistance (Typical Values)
RON = 28 mΩ at VIN = 3.6V
RON = 33 mΩ at VIN = 2.5V
RON = 42 mΩ at VIN = 1.8V
RON = 70 mΩ at VIN = 1.2V
* Maximum Quiescent Current = 1 mA
* Maximum Shutdown Current = 1 μA
SOP-8
* Low Control Input Thresholds Enable Use of 1.2V, 1.8V, 2.5V and 3.3V Logic
* Controlled Slew Rate to Avoid Inrush Currents: tR = 105μs at VIN = 3.6V
1.0V~3.6V 480mW <1000uA <1uA Typ=75mΩ Typ=0.6A SOP-8
US2236060B ULTRA-SMALL, LOW-INPUT VOLTAGE, LOW RON LOAD SWITCH

* Low Input Voltage: 1.1V~3.6V
* Ultra-Low On-State Resistance (RON)
* Typical RON values
-RON=44mΩ at VIN=3.6V
-RON =50mΩ at VIN=2.5V
-RON=58mΩ at VIN=1.8V
-RON=83mΩ at VIN=1.2V
* 1A Maximum Continuous Switch Current
* Maximum Quiescent Current < 1μA
* Maximum Shutdown Current < 1μA
* Low Control Input Thresholds Enable Use of Low-Voltage Logic
* Controlled Slew Rate to Avoid Inrush Currents
1.1V~3.6V 480mW <1uA <1uA Typ=44mΩ Typ=1A SOP-8
US2236090 ULTRA-SMALL, LOW-INPUTVOLTAGE LOW RON LOAD SWITCH

* Input Voltage: 1.1V~3.6V
* Ultra-Low ON-State Resistance
RON=66mΩ at VIN=3.6V
RON =75mΩ at VIN=2.5V
RON=90mΩ at VIN=1.8V
RON=135mΩ at VIN=1.2V
* 500mA Maximum Continuous Switch Current
* Quiescent Current < 1μA
* Shutdown Current < 1μA
* Low Control Input Threshold Enables Use of
1.2V/1.8V/2.5V/3.3V Logic
* Controlled Slew Rate (5μs Max at 3.6V)
* ESD Performance Tested Per JESD 22
2000V Human-Body Model (A114-B, Class II)
1000V Charged-Device Model (C101)
1.1V~3.6V 480mW <1uA <1uA Typ=66mΩ Typ=0.5A SOP-8
US2236090D ULTRA-SMALL, LOW-INPUTVOLTAGE LOW RON LOAD SWITCH

* Input Voltage: 1.1V~3.6V
* Ultra-Low ON-State Resistance
RON=66mΩ at VIN=3.6V
RON =75mΩ at VIN=2.5V
RON=90mΩ at VIN=1.8V
RON=135mΩ at VIN=1.2V
* 500mA Maximum Continuous Switch Current
* Quiescent Current < 1μA
* Shutdown Current < 1μA
* Low Control Input Threshold Enables Use of
1.2-V/1.8-V/2.5-V/3.3-V Logic
* Controlled Slew Rate (5μs Max at 3.6V)
* Quick Output Discharge
* ESD Performance Tested Per JESD 22
2000V Human-Body Model (A114-B, Class II)
1000V Charged-Device Model (C101)
1.1V~3.6V 480mW <1uA <1uA Typ=66mΩ Typ=0.5A SOP-8
US2236095 ULTRA-SMALL, LOW-INPUTVOLTAGE LOW RON LOAD SWITCH

* Low Input Voltage: 1.0V~3.6V
* Ultra-Low ON Resistance
-RON=78mΩ at VIN=3.6V
-RON =93mΩ at VIN=2.5V
-RON=109mΩ at VIN=1.8V
-RON=146mΩ at VIN=1.2V
* 500mA Maximum Continuous Switch Current
* Ultra Low Quiescent Current: 82nA at 1.8V
* Ultra Low Shutdown Current: 44nA at 1.8V
* Low Control Input Thresholds Enable Use of
1.2V/1.8V/2.5V/3.3V Logic
* Controlled Slew Rate to Avoid Inrush Currents: 40μs tr
* ESD Performance Tested Per JESD 22
-2000V Human-Body Model (A114-B, Class II)
-1000V Charged-Device Model (C101)
1.0V~3.6V 480mW <0.88uA <0.7uA Typ=78mΩ Typ=0.5A SOP-8
US2236095D ULTRA-SMALL, LOW-INPUTVOLTAGE LOW RON LOAD SWITCH

* Low Input Voltage: 1.0V~3.6V
* Ultra-Low ON Resistance
RON=78mΩ at VIN=3.6V
RON=93mΩ at VIN=2.5V
RON=109mΩ at VIN=1.8V
RON=146mΩ at VIN=1.2V
* 500mA Maximum Continuous Switch Current
* Ultra Low Quiescent Current: 82nA at 1.8V
* Ultra Low Shutdown Current: 44nA at 1.8V
* Low Control Input Thresholds Enable Use of
1.2V/1.8V/2.5V/3.3V Logic
* Controlled Slew Rate to Avoid Inrush Currents
US2236095: 40μs TR
* ESD Performance Tested Per JESD 22
2000V Human-Body Model (A114-B, Class II)
1000V Charged-Device Model (C101)
0.8mm×0.8mm, 0.4mm Pitch, 0.5mm Height
1.0V~3.6V 480mW <0.88uA <0.7uA Typ=78mΩ Typ=0.5A SOP-8
US2236095DB ULTRA-SMALL, LOW-INPUTVOLTAGE LOW RON LOAD SWITCH

* Low Input Voltage: 1.0V~3.6V
* Ultra-Low ON Resistance
RON=78mΩ at VIN=3.6V
RON =93mΩ at VIN=2.5V
RON=109mΩ at VIN=1.8V
RON=146mΩ at VIN=1.2V
* 500mA Maximum Continuous Switch Current
* Ultra Low Quiescent Current: 82nA at 1.8V
* Ultra Low Shutdown Current: 44nA at 1.8V
* Low Control Input Thresholds Enable Use of
1.2-V/1.8-V/2.5-V/3.3-V Logic
* Controlled Slew Rate to Avoid Inrush Currents: 220-μs tr
* ESD Performance Tested Per JESD 22
2000-V Human-Body Model (A114-B, Class II)
1000-V Charged-Device Model (C101)
1.0V~3.6V 480mW <0.88uA <0.7uA Typ=78mΩ Typ=0.5A SOP-8
US2236108DB ULTRA-SMALL, LOW-INPUTVOLTAGE LOW RON LOAD SWITCH

* Low Input Voltage: 1.0V~3.6V
* Ultra-Low ON-State Resistance
RON=90mΩ at VIN=3.6V
RON =100mΩ at VIN=2.5V
RON=114mΩ at VIN=1.8V
RON=172mΩ at VIN=1.2V
* 500mA Maximum Continuous Switch Current
* Ultra Low Quiescent Current: 82nA at 1.8V
* Ultra Low Shutdown Current: 44nA at 1.8V
* Low Control Input Thresholds Enable Use of 1.2V, 1.8V, 2.5V, 3.3V Logic
* Controlled Slew Rate to Avoid Inrush Current: 220μs
1.0V~3.6V 480mW <0.88uA <0.7uA Typ=90mΩ Typ=0.5A SOP-8
*: Under  Development