Operational Amplifier  
Single Operational Amplifier
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
M2107 Single Operational Amplifier

*Operating Voltage (V+/V- =±1.0V to±3.5V)
*Low Output Saturation: (4Vp-p at single 5V supply)
*V- Shield Plate Between +Input and -Input
*Suitable Pin Arrangement for Application
*Bipolar Technology
1 ±1.0V ~ ±3.5V or 7.0V 6 3 SOT-25
-
M2136 Ultra Wide Band, High Slew Rate Single Operational Amplifier

*Input Offset Voltage Balance
*Operating Voltage: ±1.35V ~ ±6V
*Uitra Wide Band: 200MHz Typ.
*High Slew Rate: 45V/μs Typ.
*Low Operating Current: 0.63mA Typ.
1 ±1.35V ~ ±6V 45 5 SOP-8 TSSOP-8
200MHz 
M2110 Monaural MIC Amplifier

*Operating voltage: 2.7V~5.3V
*Low operating current: V+=5V, 3.5mA (Typ,)
V+=3.3V, 1.1mA (Typ.)
*Short circuit protection for external MIC.
1 2.7V ~ 5.3V - - SOP-8 TSSOP-8
-
M2125 Single-Supply Operational Amplifier

* Single-Supply Operation
* Low Operating Voltage: ±2.7V~20V
* Low Operating Current: 1.0mA (typ.)
* Slew Rate: 1.2V/μs (typ.)
1 ±2.7V ~ 20.0V 7 1.2 SOT-25 SOT-353
1.2MHz
LM318 High-Speed Single Operational Amplifier

* Unit gain stable (internal frequency compensation)
* 4mV typical input offset voltage
* 30nA typical input offset current
* Input bias current of 250nA (maximum)
* 15MHz bandwidth (small signal)
* 50V/μs slew rate (guarantee)
* Operates voltages of ±5V to ±20V
* Overload protection for Input and output
* Same pin assignment as general-purpose op amps
1 ±5.0V ~ ±20.0V 10 70 DIP-8 SOP-8 
15MHz
LM321 Low Power Single Operational Amplifier

* Low supply current 430μA
* VCC=5V, TA=25°C. Typical values unless specified.
* Gain-Bandwidth product 1MHz
* Low input bias current 45nA
* Wide supply voltage range +3V~+32V
* Stable with high capacitive loads
1 ±2.5V ~ ±16.0V 7 0.4 SOT-23-5
1MHz
LM741* General-Purpose Single Operational Amplifier   ±2.0V ~ ±22.0V     DIP-8 SOP-8 
1MHz
*: Under  Development
Dual Operational Amplifier  
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
M2100 Dual Operational Amplifier

* Single Supply Operation
* Operating Voltage (±1.0V~±3.5V)
* Low Saturation Output Voltage
* High Slew Rate (4V/μs typ.)
* Bipolar Technology
2 ±1.0V ~ ±3.5V or 7.0V 6 4 DIP-8 SOP-8 TSSOP-8
12MHz  
M2115 Dual Operational Amplifier

* Operating Voltage: ±1V ~±7V
* Low Saturation Output Voltage: ±2.0Vp-p@V+=±2.5V
* Slew Rate: 4V/μs (typ.)
* Unity Gain Bandwidth: 12MHz (typ.)
2 ±1.0V ~ ±7.0V 6 4 DIP-8 SOP-8 TSSOP-8
12MHz 
M2137* Ultra Wide Band, High Slew Rate Operational Amplifier   ±1.35V ~ ±6.75V     DIP-8 SOP-8 TSSOP-8
200MHz
3308 Dual High Current Operational Amplifier

*Single Supply
*Operating Voltage (+3V~+15V) (±1.5V~±7.5V)
*High Output Current (150mA)
*High Frequency Noise Rejection
*Internal Enhanced Frequency Compensation
2  ±1.5V ~ ±7.5V or 3.0V ~ 15.0V 5 1 DIP-8 SOP-8 TSSOP-8
1.3MHz
3414 Dual High Current Operational Amplifier

* Single supply
* Operating voltage: 3V~15V
* High output current: 70Ma
* Slew rate: 10V/μA(Typ.)
* Bipolar technology
2  ±1.5V ~ ±7.5V or 3.0V~ 15.0V 5 1 DIP-8 SOP-8 TSSOP-8
1.3MHz
MC4556 Dual High Current Operational Amplifier

* Operating Voltage (±2V~±18V)
* High Output Current (IOUT=70mA)
* Slew Rate (3V / ms typ.)
* Gain Band Width Product (8MHz typ.)
* Bipolar Technology
2 ±2.0V ~ ±18.0V 6 3 DIP-8 SOP-8 
8MHz
MC4580 Dual Operational Amplifier

*Operating voltage (±2V ~ ±18V)
*Low input noise voltage (0.8μVrms typ.)
*Wide gain bandwidth product (15MHz typ.)
*Low distortion (0.0005% typ.)
*Slew rate (5V/μs typ.)
*Bipolar technology
2 ±2.0V ~ ±18.0V 3 5 DIP-8 SOP-8 TSSOP-8
MSOP-8 DFN2030-8 SIP-8
15MHz 
UC27L2* High Input Independence,High Gain,Low Frequency, Extremely Low
Power,Single Supply Dual Operational Amplifier
  3.0V ~ 16.0V     DIP-8 SOP-8
110KHz
MC33078 DUAL LOW NOISE OPERATIONAL AMPLIFIERS

* Dual supply operation from: ±5.0 V to ±18 V
* Low input offset voltage: 0.15mV
* Large output voltage swing: +14.1V/ -14.6V
* High slew rate: 7.0V/μs
* Low voltage noise: 4.5nV/ Hz
* Low total harmonic distortion: 0.002%
* High gain bandwidth product: 16MHz
* High open loop AC gain: 800 @ 20kHz
2 ±5.0 V to ±18 V 2 7 SOP-8 
16MHz 
MC33178 HIGH OUTPUT CURRENT LOW NOISE, LOW POWER OPERATIONAL AMPLIFIERS

* Dual supply operation from ±2V to ±18V
* High slew rate: 2.0V/μs
* Large output voltage swing
* 600Ω output drive capability
* Low offset voltage: 0.15mV (Mean)
* Low total harmonic distortion: 0.0024% (@ 1.0 kHz w/600Ω load)
* High gain bandwidth: 5.0MHz
2 ±2V to ±18V 3 2 DIP-8 SOP-8 
5MHz 
MC33272 SINGLE SUPPLY, HIGH SLEW RATE ,LOW INPUT OFFSET
VOLTAGE OPERATIONAL AMPLIFIERS

* Single (or dual) supply operation from +3 V to +36V
(±1.5V~±18V)
* Large output voltage swing: +14.1V/-14.6V
* Input offset voltage trimmed to 100μV (Typ)
* Very low input bias current: 300nA
* Very low input offset current: 3.0nA
* High input resistance: 16MΩ
* High slew rate: 10V/μs
* High gain bandwidth product: 24MHz @ 100kHz
* Low total harmonic distortion: 0.003%
* Power supply drain current: 2.15mA per amplifier
* Low noise: 18nV / Hz @ 1.0kHz
2 +3 V to +36V 1 10 SOP-8 
24MHz 
3422 High Performance Dual Operational Amplifier

* Single Supply Operation: 3V ~ 36V
* Dual Supply Operation: ±1.5V ~ ±18V
* High Gain Bandwidth Product: 25MHz
* High Slew Rate: 15V/μs
* Low Voltage Noise: 14nV/Hz
* No Phase Inversion
* ESD Tolerance: 2KV
* Latch-Up Immunity
2  ±1.5V ~ ±18.0V or 3.0V ~ 36.0V  2.5 15 DIP-8 SOP-8
25MHz
LM358 Low Power Dual Operational Amplifier

*Internally frequency compensated for unity gain.
*Wide power supply range 3V - 32V.
*Input common-mode voltage range include ground.
*Large DC voltage gain.
2  ±1.5V ~ ±16.0V or 3.0V ~ 32.0V 5 - DIP-8 SOP-8 SIP-9
MSOP-8 TSSOP-8 DFN2020-8
-
M2904 Low Power Dual Operational Amplifier

*Single Supply
*Operating Voltage: +3V~+32V
*Low Operating Current: 0.7mA (typ.)
*Slew Rate: 0.5V/μs (typ.)
2 ±1.5V ~ ±16.0V or 3.0V ~ 32.0V  7 0.5 DIP-8 SOP-8 TSSOP-8
MSOP-8
0.2MHz
MC34072 High Slew Rate, Wide Bandwidth,Dual Operational Amplifier

* Wide bandwidth: 4.5 MHz
* High slew rate: 13V/μs
* Fast settling time:1.1μs to 0.1%
* Wide single supply operation: 3.0V to 44V
* Wide input common mode voltage range:
Includes ground (VEE)
* Low input offset voltage: 3.0mV maximum
* Large output voltage swing: -14.7V to +14V
(with +-15V supplies)
* Large capacitance drive Capability: 0pF to 10,000 pF
* Low total harmonic distortion: 0.02%
* Excellent phase margin: 60°
* Excellent gain margin: 12dB
* Output short circuit protection
2 ±1.5V ~ ±22.0V or 3.0V ~ 44.0V 3 10 DIP-8 SOP-8 TSSOP-8
4.5MHz
UMC33172* High Slew Rate, Wide Bandwidth,Single Supply Operational Amplifier   ±1.5V ~ ±22.0V or 3.0V ~ 44V      DIP-8 SOP-8 TSSOP-8
MSOP-8
1.8MHz
USA5532* Dual Low-Noise Operational Amplifier   ±3.0V ~ ±20.0V     DIP-8 SOP-8 TSSOP-8
MSOP-8
10MHz
3404 Dual Operational Amplifier

*Single Supply
*Operating Voltage: +4v~+36v
*Low Operating Current: 2.0mA (Typ.)
*Slew Rate: 1.2v/ms (typ.)
2  ±2.0V ~ ±18.0V or 4.0V ~ 36.0V   5 1.2 DIP-8 SOP-8 TSSOP-8
1.2MHz
M4565 Dual Operational Amplifier.

* Operating Voltage: ±4V~±18V
* Wide Gain Bandwidth Product: 4MHz (typ.)
* Slew Rate: 4V/μs (typ.)
2 ±4.0V ~ ±18.0V 3 4 DIP-8 SOP-8 TSSOP-8
10MHz 
MC4560 Dual Operational Amplifier

*Operating Voltage (±4V~±18V)
*Wide Gain Bandwidth Product. (10MHz typ.)
*Slew Rate (4V / μs typ.)
*Bipolar Technology
2 ±4.0V ~ ±18.0V 6 4 DIP-8 SOP-8 
10MHz
MC1458 Dual Operational Amplifier

* Low power consumption
* Wide input voltage range
* No latch-up
* High gain
* Short-circuit protection
* Frequency compensation is unnecessary
2 ±22.0V 5 0.8 DIP-8 SOP-8 
1MHz 
MC4558 Dual Wide Bandwidth Operational Amplifier

* No frequency compensation required
* No latch-up
* Large common mode and differential voltage range
* Parameter tracking over temperature range
* Gain and phase match between amplifiers
* Internally frequency compensated
* Low noise input transistors
2 ±22.0V 6 2.2 DIP-8 SOP-8 TSSOP-8 SIP-9
MSOP-8
2.8MHz
LM833 Low Noise Dual Operational Amplifier

* High slew rate: 7V/μs
* High gain bandwidth product: 15MHz
* Excellent frequency stability
* Low distortion: 0.002%
* Low voltage noise: 4.5nV/Hz
2  ±2.5V ~ ±15.0V or 5.0V~ 30.0V 5 7 DIP-8 SOP-8 
15MHz
*: Under  Development
Quad Operational Amplifier  
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
LM224 Quad Operational Amplifier

* Wide Supply Voltage Range. (Single Supply: 3~30V)
* Low Supply Current Drain Independent of Supply Voltage: 0.8 mA
Typ
* Large DC voltage gain: 100dB
* Input Common-Mode Voltage Range Includes Ground.
* Low Input Bias and Offset Parameters
* Differential Input Voltage Range Equal to Maximum Rated Supply
Voltage: 32V
* Open-Loop Differential Voltage Amplification: 100 V/mV Typ
* Internal Frequency Compensation for Unity Gain
4 3.0V ~ 30.0V 5 - DIP-14 SOP-14 TSSOP-14
-
LM324 Low Power Quad Operational Amplifier

*Internally frequency compensated for unity gain.
*Large DC voltage gain :100dB.
*Wide operating supply range (Vcc=3V~40V).
*Input common-mode voltage includes ground.
*Large output voltage swing: From 0V to Vcc-1.5V.
*Power drain suitable for battery operation.
4 3.0V ~ 40.0V or ±20.0V 5 - DIP-14 SOP-14 TSSOP-14
-
MC34074 High Slew Rate, Wide Bandwidth, Quad Operational Amplifier

* Wide bandwidth: 4.5MHz
* High slew rate: 13V/μs
* Fast settling time:1.1μs to 0.1%
* Wide single supply operation: 3.0V to 44V
* Wide input common mode voltage range:
* Includes Ground (VEE)
* Low input offset voltage: 3.0mV maximum
* Large output voltage swing: -14.7V to +14V
(with +-15V supplies)
* Large Capacitance Drive Capability: 0pF to 10,000pF
* Low total harmonic distortion: 0.02%
* Excellent phase margin: 60°
* Excellent gain margin: 12dB
* Output short circuit protection
* ESD Diodes/Clamps provide input protection 
4 3.0V ~ 44.0V or ±22.0V 5 - DIP-14 SOP-14 TSSOP-14
4.5MHz
*: Under  Development
Low Voltage Rail to Rail Output Single Operational  Amplifier   
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
LV721* Low Voltage Rail to Rail Output Operational Amplifier   2.2V~5.5V     SOT-25
10MHz
LV821* Low Voltage Rail to Rail Output Operational Amplifier   2.5V~5.5V     SOT-25
5MHz
LV321 Low Voltage Rail to Rail Output Operational Amplifier

* 2.7V and 5V Performance Guaranteed
* No Crossover Distortion
* 130μA Low Supply Current
* Rail-to-Rail Output Swing @10kΩ Load: V+ -10mV
V- +65mV
* VCM From -0.2V to V+ -0.8V
1 2.7V~5.5V 7 0.8 SOT-25 SOT-353
1MHz
LLV321 Low Voltage Rail to Rail Output Operational Amplifier
* Input Voltage Varies From -0.25V to +1.5V
* Supply Current: 80μA
* Output Voltage Varies from 0.01V to 2.69V
* Gain Bandwidth: 1.2MHz
* Slew Rate: 1.5V/μs
* Fully Specified at +2.7V and +5V Supplies
* Operating Temperature Range: -40°C ~ +125°C
* Halogen Free
1 2.7V~5.5V 7 1.5 SOT-25
1.2MHz
LV2460/2461 FAMILY OF LOW-POWER RAIL-TO-RAIL INPUT/OUTPUT OPERATIONAL AMPLIFIERS
* Rail-to-Rail Output Swing
* Gain Bandwidth Product: 6.4 MHz
* ±80mA Output Drive Capability
* Supply Current: 500μA
* Input Offset Voltage: 100μV
* Input Noise Voltage: 11nV/Hz
* Slew Rate: 1.6V/μs
* Universal Operational Amplifier
1 2.7V~6.0V 7 1.6 SOT-25 SOT-26
6.4MHz
PA3211 Rail to Rail Output and High Slew Rate OP AMP

* Single-Supply Operation: +3V ~ +5.5V
* Input / Output Rail-to-Rail
* Low Quiescent Current: 500μA @ 5V
* With Low Input Current
* 5.23V/μs High Slew Rate
* High Output Driving Capacity
* 6.5MHz High Gain-Bandwidth Product
* 70dB High PSRR
1 3.0V~5.5V 10 5.2 SOT-25
6.5MHz
*: Under  Development
Low Voltage Rail to Rail Output Dual Operational  Amplifier   
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
OPA2336 Single-Supply Micropower CMOS Operational Amplifier

* Operating on a Single-Supply
* Rail-to-Rail Output (Accuracy: ± 3mv)
* Low Power Dissipation: IQ=20μA/Amplifier
* Low Offset Voltage up to 125μV (MAX.)
* Power Supply Specified from 2.3V to 5.5V
* Halogen Free
2 2.3V~5.5V 0.125 0.03 SOP-8
100KHz
LV2622 Low Voltage Rail to Rail Output Operational Amplifier

* Low Cost
* Rail-to-Rail Output Swing
* Input Rail: - 0.1V~+5.6V with VS=5.5V
* Typical VOS: 0.7mV
* Gain-Bandwidth Product: 3MHz
* High Slew Rate: 1.7V/μs
* Settling Time to 0.1% with 2V Step: 2.1μs
* Overload Recovery Time: 1μs
* Low Noise Voltage: 12nV/ Hz
* Operates on 2.5V~5.5V Supplies
* Low Power: 250μA/Amplifier Typical Supply Current
2 2.5V ~ 5.5V 3 1.7 SOP-8 MSOP-8 TSSOP-8
3MHz
LV358 Low Voltage Rail to Rail Output Operational Amplifier

* 2.7V and 5V Performance Guaranteed
* No Crossover Distortion
* 210μA Low Supply Current
* Rail-to-Rail Output Swing
@10kΩ Load V+ -10mV
V-+65mV
* VCM From -0.2V to V+ -0.8V
2 2.7V ~ 5.5V 7 1 SOP-8 TSSOP-8 MSOP-8
DFN2030-8
1MHz
*: Under  Development
             
Low Voltage Rail to Rail Output Quad Operational Amplifier   
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
LV324 Low Voltage Rail to Rail Output Operational Amplifier

* 4-Channels Op amps
* Rail-to-Rail Output Swing
* Widely Input Common-Mode Voltage Range
* Low Voltage Operation
* Low Supply Current: Typ.=410μA @ V+ =5V, V-=0V
* Perfect AC characteristics:
GBW: Typ.=1MHz
SR: Typ.=1V/μs
φm: Typ.=60Deg
Gm: Typ.=10dB.
4 2.7V ~ 5.5V 7 1 SOP-14 TSSOP-14
1.2MHz
*: Under  Development
Dual Operational Amplifier with JFET Input  
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
TL062 Low Power Dual J-FET Operational Amplifier

* Very low power consumption
* Wide common-mode (up to VCC+ ) and differential voltage range
* Low input bias and offset current
* Output short-circuit protection
* High input impedance J-FET input stage
* Internal frequency compensation
* Latch up free operation
* Typical supply current: 400μA
2 ±18.0V 15 1.1 DIP-8 SOP-8 
1MHz
TL072 Low Noise Dual J-FET Operational Amplifier

*Low power consumption
*Wide common-mode (up to VCC+ ) and differential voltage range
*Low input bias and offset current
*Low noise en = 15nV / Hz (typ)
*Output short-circuit protection
*High input impedance J-FET input stage
*Low harmonic distortion:0.01%(typ)
*Internal frequency compensation
*Latch up free operation
*High slewrate:16V/ms(typ)
2 ±18.0V 10 16 DIP-8 SOP-8 TSSOP-8
4MHz
TL082 General Purpose Dual J-FET Operational Amplifier

* Low input bias and offset current
* Wide common-mode (up to VCC
+ ) and differential voltage range
* Output short-circuit protection
* High input impedance J-FET input stage
* Internal frequency compensation
* Latch up free operation
* High slewrate:16V/μs(typ.)
2 ±18.0V 10 16 DIP-8 SOP-8 TSSOP-8
4MHz 
*: Under  Development
             
Quad Operational Amplifier with JFET Input  
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
TL064* Low Power Quad  J-FET Operational Amplifier   ±18.0V     DIP-14 SOP-14
1MHz
TL074 Low Noise Quad J-FET Operational Amplifier

*Low power consumption
*Wide common-mode (up to Vcc+ ) and differential voltage
range
*Low input bias and offset current
*Low noise eN = 15nV / Ö Hz(typ)
*Output short-circuit protection
*High input impedance J-FET input stage
*Low harmonic distortion:0.01%(typ)
*Internal frequency compensation
*Latch up free operation
*High slewrate:13V/μs(typ)
4 ±18.0V 6 13 DIP-14 SOP-14
3MHz
TL084 Low Noise Quad J-FET Operational Amplifier

*Low Power Consumption
*Wide Common-Mode (Up To Vcc+) and Differential Voltage Range
*Low Input Bias and Offset Current
*Low Noise eN = 15 (typ)
*Output Short-Circuit Protection
*High Input Impedance J-FET Input Stage
*Low Harmonic Distortion: 0.01%(typ)
*Internal Frequency Compensation
*Latch up Free Operation
4 ±18.0V 16 - DIP-14 SOP-14
1MHz
*: Under  Development
Low Voltage Rail to Rail I/O Operational Amplifier   
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
V2460* Low Power Rail-to-Rail Input/Output Single Operational Amplifier
with Shutdown
  2.7V~6.0V     SOP-8 MSOP-8 SOT-26 
6.4MHz
V2461* Low Power Rail-to-Rail Input/Output Single Operational Amplifier    2.7V~6.0V     SOP-8 MSOP-8 SOT-25
6.4MHz
V2462 Low Power Rail-to-Rail Input/Output Dual Operational Amplifier

* Rail-to-Rail Output Swing
* Gain Bandwidth Product 6.4 MHz
* ±80mA Output Drive Capability
* Supply Current 500μA/channel
* Input Offset Voltage 100μV
* Input Noise Voltage 11nV/Hz
* Slew Rate 1.6V/μs
* Universal Operational Amplifier EVM
* Available in Q-Temp Automotive
* HighRel Automotive Applications
Configuration Control/Print Support
Qualification to Automotive Standards
2 2.7V~6.0V 2 1.6 SOP-8 MSOP-8
6.4MHz
V2463* Low Power Rail-to-Rail Input/Output Dual Operational Amplifier
with Shutdown
  2.7V~6.0V     MSOP-10 SOP-10 SOP-14 
6.4MHz
V2464 Low Power Rail-to-Rail Input/Output Quad Operational Amplifier

* Rail-to-Rail Output Swing
* Gain Bandwidth Product 6.4 MHz
* ±80mA Output Drive Capability
* Supply Current 500μA/channel
* Input Offset Voltage 100μV
* Input Noise Voltage 11nV/Hz
* Slew Rate 1.6V/μs
* Universal Operational Amplifier EVM
* Available in Q-Temp Automotive
* HighRel Automotive Applications
Configuration Control/Print Support
Qualification to Automotive Standards
4 2.7V~6.0V 2 1.6 SOP-14
6.4MHz
V2465* Low Power Rail-to-Rail Input/Output Quad Operational Amplifier
with Shutdown
  2.7V~6.0V     SOP-16
6.4MHz
*: Under  Development
             
High Voltage Rail to Rail I/O Operational Amplifier   
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
LMH358 Low Power Rail to Rail Output Operational Amplifier

* Operates on 4.5V~16V supplies
* Input common voltage range beyond the rails
* Rail-to-Rail output voltage swing
* Low input offset voltage 3mV (Typical)
* High gain-bandwidth product 4MHz
* Low quiescent current: 500μA per amplifier
* Large DC voltage gain 100dB (Typical)
* High slew rate 1.3V/μs
* Unit-Gain stable
2 4.5V ~ 16V 10 1.3 SOP-8 
4MHz
L6132 Low Power 10 MHz Rail-to-Rail Input/Output Dual OP,
with Wide Supply Range 2.7V to 24.0V

* 2.7V and 5V Performance Guaranteed
* No Crossover Distortion
* 210μA Low Supply Current
* Rail-to-Rail Output Swing
@10kΩ Load V+ -10mV
V +65mV
* VCM From -0.2V to V+ -0.8V
2 1.8V ~ 24.0V 6 1 SOP-8 DFN2020-8
10MHz
ULV271* Family of 500uA/Ch 3-MHz Rail-to-Rail Output Operational Amplifier   2.7V ~ 16.0V     SOT-25 SC59-5
3MHz
ULV2371* Family of 500uA/Ch 3-MHz Rail-to-Rail Output Operational Amplifier With Shutdown   2.7V ~ 16.0V     SOT-26 SC59-6
3MHz
ULV1546 20V HIGH CURRENT DRIVE RAIL-TO-RAIL VCOM/GAMMA
BUFFER

* Wide Supply Operation Range +5V~+20V
* Beyond the rails input capability
* Rail-to-rail output swing
* Low supply current, 1.2mA per amplifier (typical)
* Wide bandwidth (unit gain) 30MHz-3dB bandwidth
* 300mA peak output AC current (typ.)
* High slew rate=30V/μs
* Unity-gain stable
4 5V~+20V 15 27 TSSOP-14
28MHz
ULV2772 FAMILY OF 2.7V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS

* Qualified for Automotive or Portable Applications
* High Slew Rate: 10.5V/μs Typ
* High-Gain Bandwidth: 5.1MHz Typ
* Supply Voltage Range from 2.5V ~ 5.5V
* Rail-to-Rail Output
* Input Offset Voltage: 360μV Typ
* Low Distortion Driving 600Ω: 0.005% THD+N
* Low Supply Current (Per Channel): 1mA
* 17nV/Hz Input Noise Voltage
* 2pA Input Bias Current
* Characterized From TA=−40°C~125°C
2 2.5V~6V 2.7 10.5 TSSOP-8 SOP-8
5.1MHz
ULV8542 1.1MHz, 42μA RAIL-TO-RAIL I/O CMOS DUAL AMPS

* Low Cost
* Operating voltage range:2.1V~ 5.5V
* Low offset voltage:0.8mV Typical
* Very low input bias currents: 0.5pA
* Rail-to-Rail Input and Output
* Unity Gain Stable
* Gain Bandwidth Product: 1.1MHz
2 2.1V~5.5V 3.5 0.8 MSOP-8
1.1MHz
*: Under  Development