Miscellaneous  
Part No. Features VCC ICC GV(dB) Package
PD(mW) IOUT IEP
HC2210* Dual Voltage Quick Heat Controller  3.5V ~ 5.5V 500uA  - DIP-8 SOP-8
500mW 20mA -
A2804 Zero Voltage Switch

*Easy operation either through the AC line or a DC supply.
*Supply voltage control.
*Very few external components.
*Symmetrical burst control-No DC current components in the load
circuit
*Negative output current pulse up to 250mA-short circuit protection.
*Reference voltage output
8.2V - - DIP-8 SOP-8
350mW 180mA -
A6966 5 DOT LED Level Meter

* Low Spurious Noise Operation.
* Constant Current Output: IOUT=8mA (Typ.)
* Indication Level Steps: 5dB, 5dB, 3dB, 3dB
* Wide Operating Supply Voltage Range: VCC = 4~ 12V
* Variable Input Amplifier Gain: GV = 0 ~ 20dB
14.0V 5mA 0 ~ 20dB SIP-9
600mW 8mA -
LA2284/A 5-DOT Dual LED Level Meter Driver

*High gain rectifying amplifier included (Gv=26dB)
*Low radiation noise when LED turns on
*Logarithmic indicator for 5-dot LED of bar type
*Constant current output(15mA)
*Wide operating supply voltage
*Not necessary diode or transistor for ALC
*Minimum number of external parts required
3.0V/3.5V ~ 16.0V 8mA 24 ~ 28dB SIP-9 MSOP-10
1100mW 11.0 ~ 18.5mA -
UCM101 Bidirectional Precision High-Side Current Monitor

* Low operating current
* High side voltage (2.7~20V)
* A fixed gain of 10
* High accuracy (typ=1%)
2.7V ~ 20.0V 50uA - SOT-25
300mW - -
UCM102 High-Side Current Monitor

* Low operating current
* High side voltage (2.5~20V)
* High accuracy (typ=1%)
2.5V ~ 20.0V - - SOT-23-3
450mW 25mA -
UA8316 IGBT Gate Driver

* A high current can directly drive IGBT
* Can directly control from a microcontroller
Source current: -200mA (max), sink current 1A (max)
* Protect the IGBT gate at power on via a diode
 7.0V ~ 24.0V GATEIN=L 8.8mA - SIP-7
925mW - -
6621 RAM MAPPLING 32×4 LCD
CONTROLLER FOR I/O μC

* Operating voltage range: 2.4V~5.2V
* External 32.768kHz crystal or 256kHz frequency source input
* Built-in 256kHz RC oscillator
* Internal time base frequency sources
* Two selectable bias (1/2 or 1/3), and three selectable duty LCD
applications (1/2 or 1/3 or 1/4).
* Two selectable buzzer frequencies (2kHz/4kHz)
* Power down command reduces power consumption
* Built-in time base generator and WDT
* Time base or WDT overflow output
* 32×4 LCD driver
* 8 kinds of time base/WDT clock sources
* Built-in 32×4 bit display RAM
* 3-wire serial interface
* Software configuration feature
* Internal LCD driving frequency source
* Data mode and command mode instructions
* VLCD pin for adjusting LCD operating voltage
* R/W address auto increment
* Three data accessing modes
2.4V~5.2V - - DIP-28 SSOP-24
- - -
UL316 SERIAL-INTERFACED 6-DIGIT LED CONTROLLER
IC WITH KEYSCAN

* LED driver with 14 outputs (8 segments/6 digits)×40 mA
load current capability for each segment
* Output pins connected directly to the LEDs or can be
open-drain
* Key-scanning (8 x 2 matrix)
* 3-wire serial bus interface (CLK, STB, DIN/DOUT)
* 8-step dimming circuit to control the overall display
brightness
* Single external resistor for output current setting
* Inputs with Schmitt trigger give superior noise
immunity
* A single LED digit output (DIG1_LED) can be used to
drive up to 8 discrete LEDs
* 8-step dimming circuit to control brightness of
individual LEDs for LED digit
* 5.0 V (± 10%) for VCC
* Drives common-anode LED digits
* Built-in power on reset and soft-start circuits
4.5V~5.5V TYP=10mA - SOP-24
1200mW IDIG = TYP120mA -
U8C3005 8 BIT SERIAL-IN PARALLEL-OUT VALVE DRIVER

* VDD range: PVDD 8V to 30V
* each channel current limit: 50mA
* Integrated internal 6V regulator
* Maximum clock frequency: 0.5MHz
* Built-in open/short detection
* Short protect
* Detecting response
* Internal reverse diode of PVDD to Absorb reverse current from coil
8.0V~30.0V TYP=3.2mA - SOP-16
1000mW - -
U8C3525 8 BIT SERIAL-IN PARALLEL-OUT VALVE DRIVER

*VDD range: VDD 5V to18V
PVDD 5V to 35V
*Maximum clock frequency: 1MHz
*current limit of Each channel:250mA
*Built-in open/short detection
*Short protect
*Detecting response
*Internal reverse diode of PVDD to Absorb reverse current from
coil
5.0V~18.0V TYP=2.3mA - SOP-16
1000mW 250mA -
TL2494 CC CONTROL FOR CAR BALLAST

* 6 ~ 40V input
* UVLO
* Open circuit protect
* Overload protect
6.0V~40.0V TYP=14mA - SOP-16
1000mW - -
VF8143 LOW-COST Three-Channel 4TH-ORDER STANDARDDEFINITION VIDEO FILTERS

* Three-Channel 4th-order 8MHz filters for SD video
* Transparent input clamping
* AC-or DC-coupled inputs
* AC-or DC-coupled outputs
* Drives single, +6dB output (150Ω)
* Drives dual, +6dB output (75Ω)
* DC-coupled outputs eliminate AC-coupling capacitors
* Single +5V power supply
* Robust 8kV ESD protection
4.75V~5.25V TYP=19mA - SOP-8
- - -
VF8146 LOW-COST SIX-CHANNEL 4TH-ORDER STANDARDDEFINITION VIDEO FILTERS

* Six-Channel 4th-order 8MHz filters for standard-Definition video
* Transparent input clamping
* AC-or DC-coupled inputs
* AC-or DC-coupled outputs
* Drives single, +6dB output (150Ω)
* Drives dual, +6dB output (75Ω)
* DC-coupled outputs eliminate AC-coupling capacitors
* Single +5V power supply
4.75V~5.25V TYP=35mA - TSSOP-14
- - -
VF8148 TRIPLE VIDEO DRIVER WITH SELECTABLE HD/SD VIDEO FILTERS FOR RGB OR YUV SIGNALS 4.75V~5.25V TYP=45mA - DIP-16
- - -
USA575 LOW VOLTAGE COMPANDOR

* Operating voltage range from 3V to 7V
* Reference voltage of 100mVRMS=0dB
* 600Ω drive capability
* One dedicated summing op amp per channel and two extra
uncommitted op amps
* Single or split supply operation
* Wide input/output swing capability
3.0V~7.0V TYP=4.2mA - SSOP-20 TSSOP-20
- - -
IR8511 IR FILTER SWITCH DRIVER

* 1.8V input driving pulse
* Low standby Current: IQSC<10uA
* 2.5V~5.5V operating voltage range
* Only one control input and Built-in non-overlap circuit to avoid the
MOSFET damage caused by the fast output voltage transient
2.5V~5.5V TYP=1mA - SOT-26
- 500mA -
UCHQ200 USB DEDICATED CHARGING PORT CONTROLLER WITH QC 2.0 FAST CHARGING FUNCTION

* Fully Supports Quick Charge 2.0 specification:
Class A: 5V, 9V, 12V Output Voltage.
Class B: 5V, 9V, 12V, 20V Output Voltage.
* Supports USB DCP Shorting D+ Line to D- Line per USB Battery Charging Specification, Revision 1.2.
* Meets Chinese Telecommunication Industrial Standard YD/T 1591-2009.
* Supports USB DCP applying 2.7V on D+ line and 2.7V on D- line.
* Supports USB DCP applying 1.2V on D+ and D- lines.
* Automatic selection of D+/D- mode for an attached device.
*Compliant with Apple and Samsung devices.
4.0V~6.0V TYP=0.6mA - SOP-8
- 500mA -
UCHQ613 USB DEDICATED CHARGING PORT CONTROLLER

* Supports USB DCP Shorting D+ Line to D– Line per USB Battery
Charging Specification, Revision 1.2 (BC1.2)
* Supports Shorted Mode (Shorting D+ Line to D-Line) per Chinese
Telecommunication Industry Standard YD/T 1591-2009
* Supports USB DCP Applying 2.7V on D+ Line And 2V on D-line (or
USB DCP Applying 2V on D+ Line and 2.7V on D– Line)
* Supports USB DCP Applying 1.2V on D+ and D– Lines
* Automatically Switch D+ and D- Lines Connections for an Attached
Device
* Dual USB Port Controller, UCHQ613
* Operating Range: 4.5V to 5.5V
4.5V~5.5V TYP=0.155mA - SOT-26
- 35mA -
URYD21 300mA BI-DIRECTION RELAY DRIVER

* Supports USB DCP Shorting D+ Line to5 to 36V input
voltage range
* Low Power Consumption (IQ<1uA)
* Input High Level Threshold: 3V, compatible with
* most single chip microcontroller
* Typical Driving Current: 300mA
* Rds(on)=15ohm(Vin=12V, PMOSFET+NMOSFET)
* Rds(on)=10ohm(Vin=20V, PMOSFET+NMOSFET)
* Peak Driving Current: 500mA@Vin=24V
* Environment Temperature: -40°C~85°C
5.0V~36.0V 0.001mA - SOT-26
- 300mA -
GF4146 GROUND FAULT INTERRUPTER

* For Two-Wire ALCI and RCD Applications
* Precision Sense Amplifier and Bandgap Reference
* Built-in AC Rectifier
* Direct DC Coupled to Sense Coil
* Low-Voltage SCR Disable
* Adjustable Sensitivity
* Built-in Noise Filter
* SCR Gate Driver
* Minimum External Components
* Meets UL 943B Requirements
* Ideal for 120V or 220V Systems
AC 120V~220V TYP=15mA - SOT-26
- 0.5mA -
ULS4X2 4X2 SWITCH MATRIX WITH TONE/POLARITY CONTROLLER

n DESCRIPTION
The UTC ULS4X2 is a low-cost 4 x 2 switch matrix with tone
detector in a 20-lead QFN package. It is used in RF multiplexing
applications from 200 to 3000 MHz. There is a 4 bit decoder and
tone/polarity detector integrated with RF switch which can reject
DiSEqC control signals. Switch may be used in 50/75 ohm
systems.
Both switch outputs (OP1 & OP2) can independently select any
of the four inputs (HH, HL, VH, VL) or simultaneously select the
same inputs. Note that the switch is bi-directional and input/output
functionality may be interchanged.
3.0V~4.2V TYP=2.0mA - QFN-20(4x4)
- - -
PCA9306 DUAL BIDIRECTIONAL I2C BUS AND SMBUS VOLTAGE-LEVEL TRANSLATOR

* 2-Bit Bidirectional Translator for SDA and SCL Lines in
Mixed-Mode I2C Applications
* I2C and SMBus Compatible
* LessThan1.5-ns Maximum Propagation Delay to
Accommodate Standard-Mode and Fast-Mode I2C
Devices and Multiple Masters
* Allows Voltage-Level Translation Between
1.2V VREF1 and 1.8-V,2.5-V,3.3-V,or 5-V VREF2
1.8V VREF1 and 2.5-V,3.3-V,or 5-V VREF2
2.5V VREF1 and 3.3-V or 5-V VREF2
3.3V VREF1 and 5-V VREF2
* Provides Bidirectional Voltage Translation With No
Direction Pin
* Low 3.5-Ω ON-State Resistance Between Input And
Output Ports Provides Less Signal Distortion
* Open-Drain I2C I/O Ports(SCL1,SDA1,SCL2,and SDA2)
* 5-V Tolerant I2C I/O Ports to Support Mixed-Mode
Signal Operation
* High-Impedance SCL1,SDA1,SCL2,and SDA2 Pins for
EN=Low
* Lockup-Free Operation for Isolation When EN=Low
* Flow-Through Pinout for Ease of Printed-Circuit-Board
Trace Routing
5.5V - - SOP-8 MSOP-8
- 128mA -
ULN2008 * Output current (single output): 100mA (MAX.)
* High sustaining voltage output: 50V (MIN.)
* Output clamp diodes
* TTL/CMOS logic level is compatible.
50V 2.5mA - SOP-16
1500 100mA -
ULN2010 * Output current (single output): 100mA (MAX.)
* High sustaining voltage output: 50V (MIN.)
* Output clamp diodes
* TTL/CMOS logic level is compatible.
50V 2.5mA - SOP-16
1500 100mA -
*: Under  Development